DIAGNOSE – BATTERY DIES DURING START ATTEMPT

SYMPTOM SUMMARY

The battery goes dead or will not start the vehicle. The engine may crank slowly for a short period then fail to crank over.

USUAL CAUSE

The battery provides the necessary energy to start the vehicle. The ignition switch will route power from the battery to the starter motor to crank the engine. Once the engine is started, the alternator will re-charge the battery and provide the necessary electrical power to operate the vehicle’s electrical system. If the alternator is defective, the battery will not recharge once the engine is started. If there is an electrical load that is on such as a glove box or courtesy light that remains on at all times, this will also drain the battery over an extended period of time. Batteries can also fail internally which can cause them to self discharge.

DIAGNOSIS

If the engine can be started via a jump start and the battery light comes on, you should suspect a failure in the charging system. You should refer to the article “Battery Light On” on this website for diagnosis of this symptom. It will be necessary to determine whether the battery is defective or there is some electrical load on the battery causing it to drain over an extended period of time. Most repair shops or part stores can charge and test the battery for a nominal fee. This should be the first step in the diagnosis. You should also inspect for electrical loads that are present even after the vehicle is shut off. The hood, trunk, and glove box lamp should be inspected to ensure they are off when the corresponding door is closed. Temporarily removing the bulb to determine if the symptom is eliminated can isolate which circuit is the cause.

Source: http://www.auto-repair-help.com/auto_diagnostics/diagnose_battery_dies_during_start_attempt.php

Autocom CDP Professional Diagnostics For Cars & Trucks

The professional compact diagnostic solution

Autocom CDP  is a diagnostic tool used wirelessly with a PC or Pocket PC, making it a powerful and

fexible tool for all vehicle shops, feet owners, vehicle testing, road service, police and armed

forces. The software chosen includes comprehensive databases of OBD functions for a wide range of

motor vehicles. Note that it is the same hardware for both passenger cars and commercial vehicles.

Options such as electrical diagrams and functional descriptions can be added to the program.

OBD Diagnosis od CDP

The OBD database includes among others the following systems: Engine, Gearbox, Service, SRS,

Instruments, ABS, Climate control, Body control etc. To obtain the most recent application list for

each database, visit: www.autocom.se/support/downloads

Autocom CDP Features

•   User-friendly and intuitive software for passenger cars, light and heavy commercial vehicles.
•   Fast and safe identifi cation of vehicles and systems
•   Bluetooth and USB connectivity are standard (W-LAN available on request)
•   Software on DVD and the internet for PC or SD card for PPC
•   User licence with regular updates
•   Quick and easy installation
•   Handles all today known communications standards for vehicle diagnostics
•   Help texts for available functions

Basic Equipment 

Autocom CDP comes with the following equipment:
•   CDP with 16-pin OBD cable (SAE J1962) for both 12 and 24 Volts
•   Software on DVD and SD card
•   USB cable
•   Database with a one year user license with updates for selected software (passenger cars or

commercial vehicles)

Cable Kit

Autocom CDP can also be supplied with complete OBD adapter cable kits for vehicles which do not

have 16-pin (J1962) diagnostic socket, including Volkswagen, Seat, Skoda, Audi, Fiat, Alfa, Lancia,

Opel, Saab, Volvo, BMW, Peugeot, Citroen, Mercedes, Renault, Ford, MAN, DAF, Scania and others

Features

•    OBD/OBDII/EOBD communication for statutory readout of the emissions related systems
•    Read and erase fault codes
•    Read real time data
•    Adjustment features
•    Restoring service messages
•    Programming features such as: injectors, keys, remote controls etc.
•    Unique multiplex technology that minimizes the need for special cables

System Requirements for PC and PPC, please visit: www.autocom.se/support/manual

Distributors

Information regarding our distributors can be found at www.autocom.se

NEW: Launch BST-460 Battery Tester

Highlights and Notice of Launch BST-460

1.Attention: This product not sell to UK, other country no problem.
2.Languages: Chinese/English/Russian
3.The world's most advanced conductance test technology
4.Scope: suitable for 6V & 12V battery system and 12V & 24V starting and charging system detects

Main Parameters

1 Shell ABS anti - acid plastic,two-tone green rubber oil ;
2.128 * 64 dot matrix,large backlit display screen (3 inches ),adjustable backlight brightness LCD display ;
3 test standards,including the most commonly used battery standard in the world,such as CCA, BCI,CA,MCA,JIS,DIN,IEC,EN,SAE,GB
4 Operating temperature:-20-60 ℃ (-4-140 ℉)

Now Price: $148.90

Advantage of Launch BST-460

Simple, secure , fast , and accurate display test results ( the test takes about 3 seconds)
Eight lines with backlight LCD display and humane language prompted interface
Does not emit light , no heat , no discharge , no spark , no operating dangerous
Automatic temperature compensation function With ripple voltage test function Multi- language menu display
Removable replacement test line
Dedicated Kelvin test clip

Advanced Functionality

Applicable to a variety of models, all kinds of batteries , and a variety of system mode
Directly detected in the car , do not need to remove the battery
Directly test the battery of the loss of electricity , bad cell battery

Test Criteria and Scope

CCA 100-2000 (SAE & BCI to develop the standard most commonly used : the cold-start battery rating )
BCI 100-2000 ( international battery Committee standards )
CA 100-2000 (0 ℃ when the effective starting current rating)
MCA 100-2000 ( ships standard effective starting current rating , 0 ℃ )
JIS 26A17 - 245H52 ( Japanese Industrial Standard)
Standard DIN 100-1400 ( German Automobile Industry Committee )
The IEC 100-1400 ( International Electrotechnical Commission.

The Introduction to NEXIQ

NEXIQ 125032 USB Link + Software Diesel Truck Interface and Software with All Installers



NEXIQ Features

1. NEXIQ is compatible with applications that diagnose engines, transmissions, ABS, instrument panels and more.
2. It will reduce the reprogramming times with direct USB connection
3. Mixed fleet capabilities with broad protocol support
3. NEXIQ can access to vehicle data for maintenance or management reports quickly
4. Quickly attaches to vehicle’s diagnostic connector.
5. Easy portability increases flexibility, may be used with desktop PC or laptop.

Specifications

RP1210A, RP1210B, and J2534 API support
USB vehicle-to-PC connectivity
Protocol coverage for automotive to heavy duty vehicles:
CAN - J1939/CAN125/CAN250/CAN500/CAN1000
2nd CAN - J1939/CAN125/CAN250/CAN500/CAN1000
Automatic bit rate detection for both CAN channels
J1587/J1708
J1850
ISO 15765 (Diagnostic CAN)
ISO 14230 (KWP2000 over ISO9141)
J2534
ALDL
ATEC 160 (160 baud)
Support windows xp and windows 7(international, isuzu softwares used in XP only)

What software NEXIQ 125032 USB Link packed with?

- Allison (Included!)
- Bendix 6.3.8.0 (Included!)
- Detroit Diesel DDDL 7.05 ((Included!)
- Detroit Diesel DDCT (Included!)
- Detroit Diesel Calibration Tool (Included!)
- Eaton Service Ranger 3.2 (Included!)
- International DLB (Included!)
- International ICAP, IPTS, NETS, IPC (Included!)
- International Master Diagnostic (Incluided!)
- Meritor and Wabco Diagnostics (Included!)
- Cummins Insite 7.5 (Included!)
- Hino 2.0.3. (Included!)
- Caterpillar 2.0.1.0 (Included!)
- Perkins EST 2010B (Included!)
- V Macks 2.6.12 (Included!)
- V Macks Dealer Pro (Included!)
- Volvo VCADS 2.35.10 (Included!)

If you want to learn how the setup NEXIQ Software, please visit http://www.youtube.com/user/shopobd2. You can learn the setup videos here.

General Information of OBDII Tools

Safety Precautions and Warnings

To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle:

>Always perform automotive testing in a safe environment.
>Wear safety eye protection that meets ANSI standards.
>Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.
>Operate the vehicle in a well ventilated work area: Exhaust gases are poisonous.
>Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
>Use  extreme  caution  when  working  around  the  ignition  coil, distributor  cap,  ignition  wires  and  spark  plugs.  These components  create  hazardous  voltages  when  the  engine  is
running.
>Put  the  transmission  in  PARK  (for  automatic  transmission)  or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
>Keep a fire extinguisher suitable for gasoline/chemical/ electrical fires nearby.
>Don’t  connect  or  disconnect  any  test  equipment  while  the ignition is on or the engine is running.
>Keep the scan tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the scan tool, when necessary.

On-Board Diagnostics (OBD) II 

The  first  generation  of  On-Board  Diagnostics (called  OBD I)  was developed  by  the California  Air  Resources  Board  (ARB)  and implemented  in  1988  to  monitor  some  of  the  emission  control components  on  vehicles.  As  technology  evolved  and  the  desire  to improve the On-Board Diagnostic system increased, a new generation of On-Board Diagnostic system was developed. This second generation of On-Board Diagnostic regulations is called "OBD II".

The OBD II system is designed to monitor emission control systems and  key  engine  components  by  performing  either  continuous  or periodic tests of specific components and vehicle conditions. When a problem is detected, the OBD II system turns on a warning lamp (MIL) on  the  vehicle  instrument  panel  to  alert  the  driver  typically  by  the phrase of “Check Engine” or “Service Engine Soon”. The system will also  store  important  information  about  the  detected  malfunction  so that a technician can accurately find and fix the problem. Here below follow three pieces of such valuable information:

1)  Whether  the  Malfunction  Indicator  Light  (MIL)  is commanded 'on' or 'off';
2)  Which, if any, Diagnostic Trouble Codes (DTCs) are stored;
3)  Readiness Monitor status.

Diagnostic Trouble Codes (DTCs) 

OBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problem found in the vehicle.
These codes identify a particular problem area and are intended to provide you with a guide as to where a fault might be occurring within a vehicle.
OBD  II  Diagnostic Trouble Codes consists of  a  five-digit  alphanumeric code. The first character, a letter, identifies which control system sets the code.  The  other  four  characters,  all  numbers,  provide  additional information on where the DTC originated and the operating conditions that caused it to set.

Location of the Data Link Connector (DLC)

The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized  16-cavity  connector  where  diagnostic  scan  tools interface  with  the  vehicle's  on-board  computer. The  DLC  is  usually located  12  inches  from  the  center  of  the  instrument  panel  (dash),
under or around the driver’s side for most vehicles. If Data Link Connector is  not  located  under  dashboard,  a  label  should  be  there telling location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must be removed to access
the  connector.  If  the  DLC  cannot  be  found,  refer  to  the  vehicle’s service manual for the location.

OBD II Readiness Monitors 

An important part of a vehicle’s OBD II system is the Readiness Monitors, which are indicators used to find out if all of the emissions components  have  been  evaluated  by  the  OBD  II  system.  They  are running periodic tests on specific systems and components to ensure
that they are performing within allowable limits.

Currently,  there  are  eleven  OBD  II  Readiness  Monitors  (or  I/M Monitors)  defined  by  the  U.S.  Environmental  Protection  Agency (EPA). Not all monitors are supported by all  vehicles and the exact number  of  monitors  in  any  vehicle  depends  on  the  motor  vehicle manufacturer’s emissions control strategy.

Continuous Monitors -- Some of the vehicle components or systems are continuously tested by the vehicle’s OBD II system, while others are  tested  only  under  specific  vehicle  operating  conditions.  The continuously monitored components listed below are always ready:
1）Misfire
2）Fuel System
3）Comprehensive Components (CCM)
Once  the  vehicle  is  running,  the  OBD  II  system  is  continuously checking  the  above  components,  monitoring  key  engine  sensors, watching for engine misfire, and monitoring fuel demands.

Non-Continuous Monitors -- Unlike the continuous monitors, many emissions  and  engine  system  components  require  the  vehicle  to  be operated under specific conditions before the monitor is ready. These monitors are termed non-continuous monitors. For  different  ignition type engines, the available monitors are different too.

The  following  monitors  are  to  be  used  for  spark  ignition  engines only:
1)  EGR System
2)  O2 Sensors
3)  Catalyst
4)  Evaporative System
5)  O2 Sensor Heater
6)  Secondary air
7)  Heated Catalyst

The  following  monitors  are  to  be  used  for compression  ignition engines only:
1)  EGR System
2)  NMHC Catalyst
3)  NOx aftertreatment
4)  Boost pressure system
5)  Exhaust gas sensor
6)  PM filter

OBD II Monitor Readiness Status

OBD II systems must indicate whether or not the vehicle’s PCM’s monitor  system  has  completed  testing  on  each  component.
Components  that have been tested will be reported as “Ready”, or “Complete”, meaning they have been tested by the OBD II system.
The  purpose  of  recording  readiness  status  is  to  allow  inspectors  to determine  if  the  vehicle’s  OBD  II  system  has  tested  all  the components and/or systems.

The power-train control module (PCM) sets a monitor to “Ready” or “Complete” after an appropriate drive cycle has been performed. The drive cycle that enables a monitor and sets readiness codes to “Ready” varies for each individual monitor. Once a monitor is set as “Ready”
or “Complete”, it will remain in this state. A number of factors, including erasing of diagnostic trouble codes (DTCs) with a scan tool or a disconnected battery, can result in Readiness Monitors being set to “Not Ready”. Since  the  three  continuous  monitors  are  constantly evaluating, they will be reported as “Ready” all of the time. If testing of  a  particular  supported  non-continuous  monitor  has  not  been completed, the monitor status will be reported as “Not Complete” or “Not Ready.”

In  order  for  the  OBD  monitor  system  to  become  ready,  the  vehicle should  be  driven  under  a  variety  of  normal  operating  conditions. These operating conditions may include a mix of highway driving and stop and go, city type driving, and at least one overnight-off period.
For specific information on getting your vehicle’s OBD monitor system ready, please consult your vehicle owner’s manual.

OBD II Definitions 

Power-train Control Module (PCM) -- OBD II terminology for the on-board computer that controls engine and drive train.

Malfunction Indicator Light (MIL) -- Malfunction Indicator Light (Service Engine Soon, Check Engine) is a term used for the light on the  instrument  panel.  It  is  to  alert  the  driver  and/or  the  repair technician  that  there  is  a  problem  with  one  or  more  of  vehicle's
systems and may cause emissions to exceed federal standards. If the MIL  illuminates  with  a  steady  light,  it  indicates  that  a  problem  has been detected and the vehicle should be serviced as soon as possible.
Under certain conditions, the dashboard light will blink or flash. This indicates  a  severe  problem  and  flashing  is  intended  to  discourage vehicle operation. The vehicle onboard diagnostic system cannot turn the MIL off until necessary repairs are completed or the condition no
longer exists.

DTC -- Diagnostic Trouble Codes (DTC) that identify which section of the emission control system has malfunctioned.

Enabling Criteria -- Also termed Enabling Conditions. They are the vehicle-specific  events  or  conditions  that  must  occur  within  the engine before the various monitors will set, or run.    Some monitors require the vehicle to follow a prescribed “drive cycle” routine as part of  the  enabling  criteria.  Drive  cycles  vary  among  vehicles  and  for each monitor in any particular vehicle.

OBD  II  Drive  Cycle -- A  specific  mode  of  vehicle  operation  that provides  conditions  required  to  set  all  the  readiness  monitors applicable  to  the  vehicle to the “ready” condition. The purpose of completing  an  OBD  II  drive  cycle  is  to  force  the  vehicle  to  run  its onboard  diagnostics.  Some  form  of  a  drive  cycle  needs  to  be performed after DTCs have been erased from the PCM’s memory or after the battery has been disconnected. Running through a vehicle’s complete drive cycle will “set” the readiness monitors so that future faults can be detected. Drive cycles vary depending on the vehicle and the  monitor  that  needs  to  be  reset.  For  vehicle  specific  drive  cycle, consult the vehicle’s Owner’s Manual.

Freeze  Frame  Data -- When  an  emissions  related  fault  occurs,  the OBD II system not only sets a code but also records a snapshot of the vehicle operating parameters to help in identifying the problem. This set  of  values  is  referred  to  as  Freeze  Frame  Data  and  may  include
important engine parameters such as engine RPM, vehicle speed, air flow,  engine  load,  fuel  pressure,  fuel  trim  value,  engine  coolant temperature, ignition timing advance, or closed loop status.

MS409 Update Instructions

While  updating  MS409,  you  will  need  to  install MaxiLink program  first.  Please  follow  the steps below to do the update.

1.  Install MaxiLink in your computer.
You can find this file in the CD came with your scan tool.

2.  Connect MS409 to your PC with the update cable.

3.  If the connection is fine, you will find the status bar at the top of MaxiLink window become green.

4.  Click “Select File” on the MaxiLink window to locate the update file.

5.  Click “Update” to begin updating your tool. When update is done, the MaxiLink will pop up a message.

6.  Power off the tool then on again to finish the update.

NOTE:  The  DTC  Lib  Update  is  a  little  different  from  the  program  update.  Please  follow  the
instructions in the window to do.

Delphi DS150E 2013 Release 1

Delphi DS150E 2013 Release 1 takes all the functionality and coverage of the DS100E (Autocom CDP) and transfers it onto a PC platform. Using the latest Bluetooth wireless technology, it supports diagnostics on around 54,000 vehicle systems and faster. On more than 4000 models from over 48 Vehicle Manufacturers. Full system coverage for BMW, VAG, Ford, Peugeot, Citroen, Renault, Vauxhall, Rover, Fiat, Volvo, Mazda, Mercedes, Smart, Nissan, Subaru, Toyota, Hyundai…and more!

Videos: Delphi Diagnostic Tool With Bluetooth

Features of Delphi DS150E

1.Bluetooth© Vehicle Communication Interfaces

2.Keeping update (the newest one Delphi 2013 release 2), compatibility better than autocom CDP.

3.New design and new Hardware, faster diagnose.

4.More the 4000 models from over 48 Vehicle Manufacturer.Including 85% European models

5.Exceptional value for money – operates from a garages existing PC

6.Full-service support available, including training programs, a technical help line and more

Languages 

English , Cesky, Dansk, Deutsch, Espanol, Francais, Greek, Hollands, Hungarian, Italiano, Norsk, Polish, Romania,Russian, Srpski, Suomen kieli, Svenska, Turkish and so on.

For more Autocom Scanners, please visit shopobd2.com.